| CGSCN 11N1 Dust low-temperature explosion-proof limit switch |
|
|
1.When using in environments with explosive gases, power cables and connectors with explosion-proof certification must be used for wiring. Always disconnect the power before opening the XCGSCN cover.
2.When opening the XCGSCN cover for maintenance, ensure the power is disconnected and wait at least 30 seconds before removing the casing.
3.For the two power interfaces, any unused port must be completely sealed with an explosion-proof certified connector.
4.Pay attention to correct polarity during wiring to avoid reverse connections.
5.Avoid excessive force during wiring to prevent insulation damage.
6.Proper grounding must be ensured in accordance with on-site and explosion-proof regulations.
|
| Selection code |
| CGSCN A B C D E F A |
| A.Explosion proof type |
0: Ordinary type |
1: Split type |
2: Low temperature type |
3:Dust and low-temperature explosion-proof type |
| B.Mechanical switch |
1:Mechanical switch (2 xSPDT) |
2: Induction switch |
C.Position transmission (2 switches only) |
—————— |
| N: not have |
0:4-20 mA output signal |
1:20-4 mA output signal |
—————— |
—————— |
| D. cable interface |
1:2-NPT1/2 |
2:2xM20x1.5 |
—————— |
—————— |
| E.Control mode (only with solenoid valve) |
—————— |
—————— |
—————— |
—————— |
| N: not have |
—————— |
—————— |
—————— |
—————— |
| S:Single electric control |
—————— |
—————— |
—————— |
—————— |
| D:Dual electric control |
—————— |
—————— |
—————— |
—————— |
| F.Supply voltage (only with solenoid valve) |
1:220VAC |
2 24VAC |
—————— |
—————— |
| In switch |
Mechanical Switch (2*SPDT) |
Inductive Proximity Sensor |
| Omron |
P+F |
|
Voltagerated
|
AC |
250V 3A
125V 5A
|
250V 10.1A
125V 10.1A
|
|
|
DC
|
250V 0.2A
125V0.4A 30V 4A
|
250V 0.2A
125V0.4A
30V 4A
|
5-60V 4-100mA
|
8-25V
|
| Terminal |
8 Point |
8 Point |
| Level ofprotection |
Ex d IIC T6 Gb Ex Td A21 IP67 T80℃ |
|
Environ mental
temperature
|
-20℃+60℃-40℃~+60℃ |
|
Scaffold
spedifications
|
2-1/2(NPT,PT,PF),M20x1.5 |
|
Scaffold
Stack specifications
|
NAMUR VDI/VDE 3845,ISO 5211 |
| Texture of timber |
Aluminium die casting |
| Weight |
1.6KG
|
Installation Method
1.Fix the bracket below the product.
2.Insert the main shaft of the product into the groove of the actuator, and then fix the bracket to the actuator.
Q: Could you offer the free samples ?
A: Yeah, but it depends products, Pls contact us ina@pneuhydr.com or whatsapp 0086 15168536055
Q: What ' s your business scope ?
A: Our business scope is service of exporter automation parts with full container, and sell air cylinder , air source treatment , solenoid valve , air valve, motorize valve , Brass valve, hydraulic valve, hydraulic cylinder, air and oil fitting, pressure gauge etc .
Q: What types of products you can make ?
A: We can make many kinds of stainless steel, brass ,aluminum materials processing .like high pressure Valve / solenoid valve / electric valve / water valve/pneumatic valve/air cylinder/hydraulic valve/hydraulic accumulator products and so on .
Q: Can the product be made with our logo and brand ?
A: Yes , of course , we can make . we are OEM supplier for years and professional to make . But you need give us the authorization if it is possible .
Q:Can you provide original famous pneumatic and hydraulic,instruments brand goods ?
A: Yes,We can supply like Festo,Smc,Ckd,Burket,Hydac,Rexroth,Siemens,Rosemount,Marsh ,Endress+Hauser etc.
Q: Is there a warranty available?
A: Yes, normally products is one year quality guarantee.
Q: Is the connector in British or Metric system? What is the difference between PT, NPT, and G threads?
A: The G thread is cylindrical and does not seal itself, requiring additional gaskets to prevent leakage. PT and NPT are conical, and the internal and external threads become tighter and tighter when tightened. Sealing is achieved through the deformation of the threads, and sealant or tape is usually used in conjunction to enhance the sealing effect
G-thread is a cylindrical straight pipe used for non sealed connections; PT thread is a conical tube that relies on the deformation and sealing of the thread itself; NPT is also a conical tube with a tooth profile angle of 60 degrees, mainly used in North America
Q: How to convert pressure units: MPa, bar, psi, kg/cm ²?
A: 1MPa=10bar≈145psi≈10kg
Q:What usually causes the burnout of solenoid valve coils?
A:Incorrect voltage and hz, frequent switching, pilot head entering liquid,valve core and spring problem,environment hot,heavy vibration etc.
Q: What should be noted for pneumatic components in high temperature or extremely cold environments?
| Focus Point |
High Temperature Environment Countermeasures |
Extreme Cold Environment Countermeasures |
| Seals |
Fluororubber, PTFE |
Low-temperature nitrile, silicone rubber, polyurethane |
| Lubrication |
High-temperature synthetic grease (low volatility) |
Low-temperature grease (low pour point, low viscosity) |
| Air Supply Treatment |
Strengthen cooling, efficient water removal |
Ultra-low dew point drying (refrigeration + adsorption type), heat tracing |
| Metal Components |
Reserve expansion clearance |
Select materials with low-temperature toughness, prevent leakage due to cold shrinkage |
| Control Components |
High heat-resistant grade coils, heat dissipation, low power consumption |
Install insulation boxes, local heating, prevent cold condensation |
| Installation |
Keep away from heat sources, add heat insulation plates |
Avoid exposure to wind and snow, wrap with thermal insulation materials |
Your message must be between 20-3,000 characters!
English
